Simrad 38-9 - REV B Installation Manual Page 42
- Page / 136
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Getting started
33
857-160970 / Rev.H
Range field
The Range field allows you to read and specify the range used
in the Echogram field. The current range is displayed on the
range axis. In the Range dialogue box you can define the area of
interest for the echogram.
Position the cursor in the Range field, click the right mouse
button. Observe a dialogue box referring to either Surface or
Bottom depending on your choice in the Echogram dialogue
box.
In this case, check that you have the Surface Range dialogue
open.
Set Range to 200 m and Start Relative Surface to0m,then
click OK to accept the settings.
Comments to the Echogram and Range view
Two echograms are shown for each Channel. The second
echogram for the present Channel maybeusedinthecurrent
example to show the distribution of fish close to the bottom.
• Use the Echogram dialogue in the second Echogram view
to set the Echogram to Bottom and choose the School gain
TVG function for calculating S
V
-values.
• Use the corresponding Bottom Range dialogue to set Range
to 20 m and Stop Relative Bottom to 5 m for the echogram
to show values calculated from 15 m above the detected
bottom to 5 m below the bottom.
Remember that the area of interest defined in the Echogram
view is also used for the Single Echo Detection view limits.
When you place the cursor in the Echogram field, you can use
the mouse wheel to modify the receiver gain level, and hence
the display colour sensitivity. Each click of the wheel
corresponds to a 1 dB change. The same colour sensitivity
setting is available from the Color Scale dialogue box.
Whenever the cursor is located within the Echogram field, a
small yellow label is visible. The label provides the following
information:
• Left: Depth at the cursor position
• Middle: Diameter coverage at the transducer beam at the
current cursor position
• Right: Current gain setting
To change the range, you can also use the mouse wheel. Place
the cursor inside the Range fieldtodothis:
- Reference manual 1
- Fish finding echo sounder 3
- Document revisions 4
- About this document 4
- Chapters 5
- Table of contents 6
- SYSTEM DESCRIPTION 10
- System overview 11
- System diagram: 12
- Wave propagation 13
- → Environment, page 89 14
- → Echogram, page 85 14
- Bottom echo 15
- Split-beam operation 17
- Observation range 19
- DISPLAY VIEWS 21
- (CD10202) 22
- Moving the boundary lines 23
- (CD10204) 25
- (CD10205) 26
- (CD10206) 27
- Echogram and Range 28
- Status bar 30
- History and printer views 31
- Display example 32
- Printer example 32
- GETTING STARTED 35
- → ES60 Installation manual 36
- Start-up 37
- Navigation interface 38
- Additional interfaces 38
- Display views chapter 39
- Bottom detector settings 40
- Colour scale 40
- Single Echo view 40
- Echogram and Range view 41
- Range field 42
- Color Scale dialogue box 42
- Scope view 43
- → Store, page 113 45
- OPERATIONAL PROCEDURES 46
- Power on/off 47
- Operational procedures 48
- Basic operations 49
- Changing the transmit power 50
- Enabling the depth alarms 51
- Adding annotations 51
- Transceiver installation 53
- To modify an IP address 54
- Restart the echo sounder 54
- Record and playback 55
- Playback 57
- (CD5639A) 59
- Overview 60
- Software upgrade procedure 61
- Un-installation procedure 61
- REFERENCE GUIDE 66
- Main menu 67
- File menu 68
- View menu 69
- Options menu 70
- Restore settings 71
- Install menu 72
- BI500 dialogue box 73
- Help menu 74
- Status Bar 75
- Reference guide 76
- Dialogue boxes 77
- Advanced Navigation 78
- Advanced Transceiver 80
- Annotation 82
- Datagram 85
- Bottom Detector 87
- Bottom Range 89
- Colour Scale 90
- Removing colours 91
- Depth Output 92
- Echo Trace 93
- Echogram 94
- Horizontal Depth Lines 95
- Vertical Markers 96
- Environment 98
- Shutdown 99
- Factory settings 100
- Fish select 101
- Heave Sensor 102
- 857-160970 / Rev.H 103
- Related topics 104
- → Operation, page 102 104
- → History recording, page 48 104
- IP Address 105
- Language 107
- Arrangement 108
- Channels 108
- Navigation Interface 109
- Operation 111
- External trigger 112
- Printer and History 114
- Print Setup 116
- Purse Seine 118
- Simrad ES60 119
- Survey (directory) 119
- Selected Files 119
- RS-232 Setup 121
- Data formats 122
- Surface Range 124
- Temperature Sensor 125
- Transceiver Installation 126
- Transceiver Settings 128
- Transmit Power 129
- Pulse Length 129
- Transducer 129
- Trawl Interface 131
- Trawl Range 133
- E 2006 Simrad Horten AS 136
- ISBN 82-8066-028-3 136
Related products and manuals for Network transceiver modules Simrad 38-9 - REV B
(148 pages)© 2020, manymanuals.com. All rights reserved. | 0.332 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals