Simrad NX45 Specifications Page 102
- Page / 120
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Simrad NX40/45 Installation and Operation Manual102
20-3 Installation: The display unit
Start by selecting a suitable mounting position for the
NX40/45 display unit:
Consider the best possible position for viewing and •
operating the NX40/45. This will generally be a
relatively shaded area free from obstructions.
At least 100 mm (4”) away from the compass, at •
least 300 mm (12”) away from any radio transmitter
and at least 1.2 m (4 ft) away from any antenna.
For optimum performance and reliability consider •
mounting the unit where it will not be unnecessarily
exposed to direct sunlight, water and protected from
other physical damage which could occur during
rough sea passages.
If bracket mounting chose a at area where the •
display will not be subjected excessive vibration.
Select an area with adequate clearance for cabling •
and access to the power source.
Before drilling any holes ensure that the drill area is •
free from cables or other obstructions.
There are two mounting arrangements:
Flush Mounting the NX40/45
Attach the ush mounting template to the selected •
mounting position using adhesive tape.
Drill a pilot hole for each of the hole saw cuts shown •
on the template before cutting the larger hole with
the hole saw.
Next cut all the way around the inside of the cut-out •
line with a saw to remove the waste material shown
on the template.
Check that the unit ts correctly in the cut out area. •
Adjust the t with a le if required.
Select a 2-3.5 mm 1/8” drill bit depending on •
hardness of material to drill. Smaller diameter holes
will be needed for soft woods and larger diameter
pilot holes will be required if mounting to hard
materials such as berglass (we recommend 3.5
mm (1/8”) for berglass and Aluminum).
With the selected drill bit drill the 4 pilot holes for the •
8 gauge screws used to attach the unit. These are
indicated on the corners of the mounting template.
Connect all cables to the rear of the unit before •
placing the unit into the console.
Firmly secure the unit in place with the 4 x 8 gauge •
self tapping screws.
Note: the 5 x 14G self tapping screws are for bracket
mounting only.
- NX40/45 1
- NavStation 1
- Contents 3
- Overview1 7
- 1-3 Plug-in cards 8
- Removing the display unit 9
- Replacing the display unit 9
- Basic Operation2 10
- 2-4 Man overboard (MOB) 13
- 2-5 Alarms 13
- 2-7 The main windows 14
- 2-6 Simulate mode 14
- Simulate > Simulate > 14
- > More 15
- Red border 16
- Navigation: Chart3 19
- 3-2 Chart window 21
- 3-2-1 Chart modes 22
- 3-2-2 Latitude and longitude 22
- 3-5 Tracks and tracking 25
- 3-4 Projected course 25
- Video window4 26
- Navigation: Highway window5 27
- Navigation: Waypoints6 28
- Navigation: Routes7 31
- Satellites8 35
- 9-1 Using the unit 36
- 9-2 Interpreting the display 37
- Strength of echoes 37
- Frequency and cone width 38
- Bottom types 38
- When to use Mixed 40
- When to use 50/200 kHz 40
- 50 kHz display 41
- 200 kHz display 41
- Where to nd sh 42
- Fish arches 42
- 9-5 Range 43
- Range > 43
- Zoom range and offset 43
- 9-6 Gain and threshold 43
- The gain window 44
- Threshold 44
- Echosounder10 45
- 10-1-1 Extended history mode 46
- Bottom lock > On or Off 47
- 10-3 Echosounder split window 47
- Setting gain and threshold 48
- Fish recognition 48
- Bottom type 48
- Gauges window11 49
- Data window12 50
- Fuel functions and display13 51
- B - Part ll a tank 53
- Add fuel 53
- C - Removing fuel 53
- Set remaining 53
- Set Remaining menu to 53
- For Example 1 55
- 13-6 Fuel consumption curves 55
- 13-7 Calibration 58
- Fuel > Setup engines 58
- Calibrate and change 58
- Tides window14 59
- User card window15 60
- 16-1 Viewing AIS Vessels 62
- TCPA 15 min 63
- CPA 0.5 nm 63
- Safety msgs (rx) 64
- to turn SmartCraft Off 65
- or > to conrm 66
- to conrm 66
- 17-3-4 Trim indicator 68
- Radar 18 70
- 18-6-1 Changing the gain mode 72
- Adjust Radar > Gain Mode 72
- oating VRM/EBL 76
- from the center to give 77
- Setting up the NX40/4519 80
- 19-1 Setup > System 81
- 19-2 Setup > Chart 82
- If you select a map datum 83
- It should 83
- Set > 84
- General submenu 84
- Land submenu 85
- Other submenu 85
- 19-4 Setup > Radar 87
- Radar > Installation 90
- 19-5 Setup > GPS 91
- 19-6 Setup > Fuel 92
- 19-7 Setup > Track 93
- 19-8 Setup > AIS 94
- 19-11 Setup > Units 96
- 19-12 Setup > Comms 96
- 19-13 Setup > Calibrate 97
- Calibrate 97
- 19-14 Setup > Time 98
- 19-15 Setup > Favorites 99
- 19-16 Setup > Simulate 99
- Simulate 99
- Installation 20 100
- GA B C D E F 101
- Flush Mounting the NX40/45 102
- Bracket Mounting the NX40/45 103
- Installing an antenna 105
- Echosounder to 105
- 20-9 Installation: SmartCraft 106
- 20-10 Installation: Radar 107
- Power cable 108
- Specications21 109
- COMMUNICATIONS 110
- STANDARDS COMPLIANCE 110
- Simrad NX45 111
- Simrad NX40 111
- List of datums 112
- Troubleshooting22 113
- B-3 Fuel consumption problems 114
- Economy 114
- B-4 echosounder shnding 115
- B-5 Radar problems 116
- Navigation data24 118
- Compliance statements25 119
Related products and manuals for Car navigation systems Simrad NX45
(100 pages)© 2020, manymanuals.com. All rights reserved. | 0.183 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals