Simrad NX45 Specifications Page 78
- Page / 120
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Simrad NX40/45 Installation and Operation Manual78
Set. Offset the PPI center in the radar window. (This •
works only when you are using relative motion (RM)
mode). Use the arrow keys to move the PPI center
to the new position then press
to conrm. The
new position must allow most of the radar sweep
to appear on the radar window; if it doesn’t, the
PPI center will be moved as close as possible to the
desired position.
18-11 Using the radar guard zones
Use either or both of the two radar guard zones and
alarms to notify you when a target enters or exits a
specied area around your boat.
From the radar window >
> Guard zone
18-11-1 Turning a radar guard zone on or
off
Two radar guard zones are available. From the
Guard zone menu:
Zone > 1 selects radar guard zone 1, 2 selects radar
guard zone 2 > Set Enable to (show the radar guard
zone) or (hide the radar guard zone)
18-11-2 Change the setting for a radar
guard zone alarm
Guard Zone
> Alarm when > Enter sounds the alarm
only when a target enters / Exit sounds the alarm only
when a target leaves / Both sounds the alarm when a
target enters or leaves the radar guard zone.
When a radar guard zone is on, the guard zone alarm is
set automatically but you can change the setting to suit
your preferences.
18-11-3 Adjusting the boundaries of a radar
guard zone
From the Zone menu > Adjust
i • Guard Zone The number shows the radar guard
zone that is selected.
ii • Sector or Circular The shape of the radar guard
zone.
iii • IN RANGE The distance between the inner
boundary and your boat.
iv • OUT RANGE The distance between the outer
boundary and your boat.
- NX40/45 1
- NavStation 1
- Contents 3
- Overview1 7
- 1-3 Plug-in cards 8
- Removing the display unit 9
- Replacing the display unit 9
- Basic Operation2 10
- 2-4 Man overboard (MOB) 13
- 2-5 Alarms 13
- 2-7 The main windows 14
- 2-6 Simulate mode 14
- Simulate > Simulate > 14
- > More 15
- Red border 16
- Navigation: Chart3 19
- 3-2 Chart window 21
- 3-2-1 Chart modes 22
- 3-2-2 Latitude and longitude 22
- 3-5 Tracks and tracking 25
- 3-4 Projected course 25
- Video window4 26
- Navigation: Highway window5 27
- Navigation: Waypoints6 28
- Navigation: Routes7 31
- Satellites8 35
- 9-1 Using the unit 36
- 9-2 Interpreting the display 37
- Strength of echoes 37
- Frequency and cone width 38
- Bottom types 38
- When to use Mixed 40
- When to use 50/200 kHz 40
- 50 kHz display 41
- 200 kHz display 41
- Where to nd sh 42
- Fish arches 42
- 9-5 Range 43
- Range > 43
- Zoom range and offset 43
- 9-6 Gain and threshold 43
- The gain window 44
- Threshold 44
- Echosounder10 45
- 10-1-1 Extended history mode 46
- Bottom lock > On or Off 47
- 10-3 Echosounder split window 47
- Setting gain and threshold 48
- Fish recognition 48
- Bottom type 48
- Gauges window11 49
- Data window12 50
- Fuel functions and display13 51
- B - Part ll a tank 53
- Add fuel 53
- C - Removing fuel 53
- Set remaining 53
- Set Remaining menu to 53
- For Example 1 55
- 13-6 Fuel consumption curves 55
- 13-7 Calibration 58
- Fuel > Setup engines 58
- Calibrate and change 58
- Tides window14 59
- User card window15 60
- 16-1 Viewing AIS Vessels 62
- TCPA 15 min 63
- CPA 0.5 nm 63
- Safety msgs (rx) 64
- to turn SmartCraft Off 65
- or > to conrm 66
- to conrm 66
- 17-3-4 Trim indicator 68
- Radar 18 70
- 18-6-1 Changing the gain mode 72
- Adjust Radar > Gain Mode 72
- oating VRM/EBL 76
- from the center to give 77
- Setting up the NX40/4519 80
- 19-1 Setup > System 81
- 19-2 Setup > Chart 82
- If you select a map datum 83
- It should 83
- Set > 84
- General submenu 84
- Land submenu 85
- Other submenu 85
- 19-4 Setup > Radar 87
- Radar > Installation 90
- 19-5 Setup > GPS 91
- 19-6 Setup > Fuel 92
- 19-7 Setup > Track 93
- 19-8 Setup > AIS 94
- 19-11 Setup > Units 96
- 19-12 Setup > Comms 96
- 19-13 Setup > Calibrate 97
- Calibrate 97
- 19-14 Setup > Time 98
- 19-15 Setup > Favorites 99
- 19-16 Setup > Simulate 99
- Simulate 99
- Installation 20 100
- GA B C D E F 101
- Flush Mounting the NX40/45 102
- Bracket Mounting the NX40/45 103
- Installing an antenna 105
- Echosounder to 105
- 20-9 Installation: SmartCraft 106
- 20-10 Installation: Radar 107
- Power cable 108
- Specications21 109
- COMMUNICATIONS 110
- STANDARDS COMPLIANCE 110
- Simrad NX45 111
- Simrad NX40 111
- List of datums 112
- Troubleshooting22 113
- B-3 Fuel consumption problems 114
- Economy 114
- B-4 echosounder shnding 115
- B-5 Radar problems 116
- Navigation data24 118
- Compliance statements25 119
Related products and manuals for Car navigation systems Simrad NX45
(100 pages)© 2020, manymanuals.com. All rights reserved. | 2.438 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals