Simrad NX45 Specifications Page 94
- Page / 120
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Simrad NX40/45 Installation and Operation Manual94
19-8 Setup > AIS
> AIS
Note: This feature requires an AIS receiver.
Filter by Type Vessel types that are not selected
will be filtered off the chart. Default
is set to all types enabled allowing all
vessels to be shown on the chart.
Filter by distance Vessels outside the radius selected
from our current position are filtered
off the chart. Default value is set
to 300 nm allowing all vessels to
be shown on the chart within that
distance.
Filter by speed Vessels with speed below the value
selected are filtered off the charts.
Default is set to 0 nm allowing all
vessels to be shown onto the chart.
Sym-
bol
Alarm Beeper Alarm sounds when it is on and the:
Arrival radius Boat is closer to the destination or to a waypoint than the
alarm trigger value
Anchor alarm Boat moves by more than the alarm trigger value
XTE Boat moves off course by more than the CDI scale
Danger Boat comes closer to a danger waypoint than the alarm
trigger value
Too shallow
1
/
5
sec Depth is less than the alarm trigger value
Too deep
1
/
2
sec Depth is greater than the alarm trigger value
Fish 1 short
beep
Echo matches the prole of a sh
Temperature
1
/
2
sec Temperature equals the alarm trigger value
Temperature
rate
1
/
2
sec Rate of change of temperature equals the alarm trigger
value
Low battery
1
/
2
sec Battery voltage is less than the alarm trigger value
Low fuel
1
/
2
sec Low fuel remaining equals the alarm trigger value; on a
multitank boat you can set separate alarms for each tank
Loss of DGPS
x
unit can not receive the DGPS signal (beacon, WAAS or
EGNOS)
Loss of GPS
x
unit can not receive the GPS signal (this alarm is always
on)
Loss of AIS
receiver
comms
NX40/45 is no longer receiving communication from the
AIS receiver (Alarm is on when AIS is enabled)
Dangerous
vessel
The TCPA/CPA of another vessel is less than the trigger
values
- NX40/45 1
- NavStation 1
- Contents 3
- Overview1 7
- 1-3 Plug-in cards 8
- Removing the display unit 9
- Replacing the display unit 9
- Basic Operation2 10
- 2-4 Man overboard (MOB) 13
- 2-5 Alarms 13
- 2-7 The main windows 14
- 2-6 Simulate mode 14
- Simulate > Simulate > 14
- > More 15
- Red border 16
- Navigation: Chart3 19
- 3-2 Chart window 21
- 3-2-1 Chart modes 22
- 3-2-2 Latitude and longitude 22
- 3-5 Tracks and tracking 25
- 3-4 Projected course 25
- Video window4 26
- Navigation: Highway window5 27
- Navigation: Waypoints6 28
- Navigation: Routes7 31
- Satellites8 35
- 9-1 Using the unit 36
- 9-2 Interpreting the display 37
- Strength of echoes 37
- Frequency and cone width 38
- Bottom types 38
- When to use Mixed 40
- When to use 50/200 kHz 40
- 50 kHz display 41
- 200 kHz display 41
- Where to nd sh 42
- Fish arches 42
- 9-5 Range 43
- Range > 43
- Zoom range and offset 43
- 9-6 Gain and threshold 43
- The gain window 44
- Threshold 44
- Echosounder10 45
- 10-1-1 Extended history mode 46
- Bottom lock > On or Off 47
- 10-3 Echosounder split window 47
- Setting gain and threshold 48
- Fish recognition 48
- Bottom type 48
- Gauges window11 49
- Data window12 50
- Fuel functions and display13 51
- B - Part ll a tank 53
- Add fuel 53
- C - Removing fuel 53
- Set remaining 53
- Set Remaining menu to 53
- For Example 1 55
- 13-6 Fuel consumption curves 55
- 13-7 Calibration 58
- Fuel > Setup engines 58
- Calibrate and change 58
- Tides window14 59
- User card window15 60
- 16-1 Viewing AIS Vessels 62
- TCPA 15 min 63
- CPA 0.5 nm 63
- Safety msgs (rx) 64
- to turn SmartCraft Off 65
- or > to conrm 66
- to conrm 66
- 17-3-4 Trim indicator 68
- Radar 18 70
- 18-6-1 Changing the gain mode 72
- Adjust Radar > Gain Mode 72
- oating VRM/EBL 76
- from the center to give 77
- Setting up the NX40/4519 80
- 19-1 Setup > System 81
- 19-2 Setup > Chart 82
- If you select a map datum 83
- It should 83
- Set > 84
- General submenu 84
- Land submenu 85
- Other submenu 85
- 19-4 Setup > Radar 87
- Radar > Installation 90
- 19-5 Setup > GPS 91
- 19-6 Setup > Fuel 92
- 19-7 Setup > Track 93
- 19-8 Setup > AIS 94
- 19-11 Setup > Units 96
- 19-12 Setup > Comms 96
- 19-13 Setup > Calibrate 97
- Calibrate 97
- 19-14 Setup > Time 98
- 19-15 Setup > Favorites 99
- 19-16 Setup > Simulate 99
- Simulate 99
- Installation 20 100
- GA B C D E F 101
- Flush Mounting the NX40/45 102
- Bracket Mounting the NX40/45 103
- Installing an antenna 105
- Echosounder to 105
- 20-9 Installation: SmartCraft 106
- 20-10 Installation: Radar 107
- Power cable 108
- Specications21 109
- COMMUNICATIONS 110
- STANDARDS COMPLIANCE 110
- Simrad NX45 111
- Simrad NX40 111
- List of datums 112
- Troubleshooting22 113
- B-3 Fuel consumption problems 114
- Economy 114
- B-4 echosounder shnding 115
- B-5 Radar problems 116
- Navigation data24 118
- Compliance statements25 119
Related products and manuals for Car navigation systems Simrad NX45
(100 pages)© 2020, manymanuals.com. All rights reserved. | 0.816 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals