Simrad GC80 Instruction Manual Page 99
- Page / 112
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
DIP SWITCH SETTINGS
20221511 / C 91
Jumper settings on ICIF board
JUMPER DEFAULT FUNCTION DESCRIPTION
J5 Short Software installation Open = Software may be installed on ICIF
board
NOTE
: Make sure that also J1 on the IOPT
board is set to “Open”
NOTE
: Control unit will be damages if new
software is installed with this jumper
ON!
J6 Open CUP reset Used when resetting the CPU
J7 3-4 short Output port: ITERM board, TB1 “1TX”
1-2 short = IEC61162-2 or TOKIMEC version
3-4 short = IEC61162-1 ed.2
(ref. page 4)
NOTE
: Never use both jumpers at the same
time!
J8 3-4 short Output port: ITERM board, TB1 “2TX”
1-2 short = IEC61162-2 or TOKIMEC version
3-4 short = IEC61162-1 ed.2
(ref. page 4)
NOTE
: Never use both jumpers at the same
time!
J9 3-4 short Output port: ITERM board, TB1 “3TX”
1-2 short = IEC61162-2 or TOKIMEC version
3-4 short = IEC61162-1 ed.2
(ref. page 4)
NOTE
: Never use both jumpers at the same
time!
J10 3-4 short
Output serial signal
selection
Output port: ITERM board, TB1 “4TX”
1-2 short = IEC61162-2 or TOKIMEC version
3-4 short = IEC61162-1 ed.2
(ref. page 4)
NOTE
: Never use both jumpers at the same
time!
J11 1-2 short Polarity for “GPS”
signal setting
Input port: ITERM board, TB2 “GRX”
1-2 short = Standard
3-4 short = Reversed polarity
NOTE:
If a signal not is received with 1-2
short, 3-4 should be set to short.
NOTE
: Never use both jumpers at the same
time!
J14 3-4 short Alarm contact output Output port: ITERM board, TB1 “ALCN”
- SIMRAD GC80/85 1
- COMPACT 1
- Document revisions 2
- Document history 2
- About this manual 3
- Contents 5
- 20221511 / C vii 7
- 1 SYSTEM OVERVIEW 9
- 1.1 Introduction 10
- 1.2 Precaution in use 11
- 1.3 System components 12
- 1.4 Bearing repeaters 12
- 2 USER INTERFACE 13
- POWER Button 14
- Display 14
- GYRO Button 14
- EXT Button 14
- DISP Button 15
- SET Button 15
- ACK/ENT Button 15
- Arrow Buttons 15
- Alarm Indicator 15
- 8 20221511 / C 16
- 3 OPERATION 17
- Start-Up 18
- Turning the Gyro compass OFF 19
- 3.3 Adjusting dimming level 20
- 20221511 / C 22
- True bearing 23
- Latitude 23
- Speed error correction 24
- OPERATION 25
- 3.6 Pendulum function 26
- 3.7 Alarm messages 27
- Acknowledging an alarm 28
- 4 MAINTENANCE 29
- POWER button is turned 30
- Mechanical installation 31
- 20221511 / C 25 33
- 20221511 / C 27 35
- Parameter updates 36
- SET button, and then 37
- 4.8 Replacing the Fuses 38
- 20221511 / C 31 39
- Power Supply Unit (Option) 40
- 5 INSTALLATION 41
- 5.1 Unpacking and handling 42
- 5.2 Mechanical installation 42
- Control unit 43
- Power supply unit (Option) 45
- Master compass 46
- 5.3 Cabling 47
- 5.4 Grounding the units 48
- 5.5 Dip-switch settings 48
- Configuring the Control unit 49
- 20221511 / C 43 51
- 20221511 / C 45 53
- System Start-up 55
- Configuring the gyro system 56
- 20221511 / C 49 57
- ACK/ENT button 58
- ACK/ENT 58
- ACK/ENT button 59
- Adjusting True heading 60
- 20221511 / C 53 61
- 54 20221511 / C 62
- 6 ADVANCED SETTINGS 63
- 6.1 General 64
- 20221511 / C 57 65
- 58 20221511 / C 66
- ADVANCED SETTINGS 67
- 60 20221511 / C 68
- 62 20221511 / C 70
- 7 TECHNICAL SPECIFICATION 71
- 7.1 Accuracy 72
- 7.2 General specification 72
- 7.3 Input specification 73
- 7.4 Output specification 74
- 7.5 Physical Dimensions 75
- 7.6 Power 75
- GC80 Compact Control Unit 76
- GC80/85 Master Compass 76
- GC80 Compact Control unit 76
- 8 DRAWINGS 77
- 8.1 Drawings included 78
- DRAWINGS 79
- 72 20221511 / C 80
- 74 20221511 / C 82
- 76 20221511 / C 84
- 9 SPARE PART LIST 85
- 78 20221511 / C 86
- SPARE PART LIST 87
- 80 20221511 / C 88
- 10 TERMINAL LAYOUT 89
- 10.1 ITERM board 90
- TERMINAL LAYOUT 91
- 10.2 IOPT board 93
- 86 20221511 / C 94
- 11 DIP SWITCH SETTINGS 95
- 11.1 Compact control unit 96
- ICIF board 97
- 90 20221511 / C 98
- DIP SWITCH SETTINGS 99
- IOPT board 100
- 20221511 / C 93 101
- ITERM board 102
- ACTIONS 103
- 12.1 The alarm system 104
- 12.2 Acknowledging an alarm 105
- 12.3 Fault finding 106
- Inverter failure 107
- Zero cross failure 107
- System communication failure 108
- 20221511 / C 101 109
- Repeater failure 110
- 20221511 / C 103 111
- 104 20221511 / C 112
Related products and manuals for Navigational compasses Simrad GC80
(36 pages)© 2020, manymanuals.com. All rights reserved. | 0.441 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals