Simrad NX45 Specifications Page 118
- Page / 120
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Simrad NX40/45 Installation and Operation Manual118
Navigation data24
BRG Bearing to Destination: Bearing to the destination from the boat.•
• BRG Bearing to cursor: Bearing to cursor from boat
CDI Course Deviation Indicator: When the boat is navigating to a point, the •
chart and highway windows show a parallel line on either side of the plotted
course. These two lines are called the Course Deviation Indicator (CDI) lines.
The distance from the plotted course to a CDI line is the CDI scale.
Set the CDI scale to the maximum distance that the boat should deviate from the •
plotted course. The chart and highway windows show the CDI lines, which
are like a highway over the water where the boat will move. The windows
show how far the boat has deviated from the plotted course and if the boat is
approaching a CDI line. If the XTE alarm is enabled an alarm will sound if the
boat reaches a CDI line.
COG Course Over Ground: Direction in which the boat is moving over the •
ground.
CTS Course To Steer: Optimum course to steer to return to the plotted course.•
DTG Distance To Go: Distance from the boat to the destination.•
ETA Expected Time of Arrival: At the destination, assuming that SOG and COG •
remain constant.
• DST Distance from boat to cursor
SOG Speed Over Ground: Current boat speed over the ground. This is not •
necessarily the same as the boat speed through the water nor the speed at
which it is approaching the destination.
STR Steering: The difference between COG and CTS.•
TTG Time To Go: The estimated time to reach the destination.•
XTE Cross Track Error: The distance from the boat to the nearest point of the •
plotted course. XTE may have a letter: R means steer to the right to return
to the plotted course, L means steer to the left.
VMG Velocity Made Good: The speed at which the boat is approaching the •
destination.
CTS
SOG (speed)
VMG (speed)
BRG
COG
Destination
Boat position
Start
STR
DTG
(distance)
CDI scale
(distance)
Plotted
course
Start
Destination
XTE
(distance)
Boat
position
CDI scale
(distance)
CDI line
Plotted
course
CDI line
- NX40/45 1
- NavStation 1
- Contents 3
- Overview1 7
- 1-3 Plug-in cards 8
- Removing the display unit 9
- Replacing the display unit 9
- Basic Operation2 10
- 2-4 Man overboard (MOB) 13
- 2-5 Alarms 13
- 2-7 The main windows 14
- 2-6 Simulate mode 14
- Simulate > Simulate > 14
- > More 15
- Red border 16
- Navigation: Chart3 19
- 3-2 Chart window 21
- 3-2-1 Chart modes 22
- 3-2-2 Latitude and longitude 22
- 3-5 Tracks and tracking 25
- 3-4 Projected course 25
- Video window4 26
- Navigation: Highway window5 27
- Navigation: Waypoints6 28
- Navigation: Routes7 31
- Satellites8 35
- 9-1 Using the unit 36
- 9-2 Interpreting the display 37
- Strength of echoes 37
- Frequency and cone width 38
- Bottom types 38
- When to use Mixed 40
- When to use 50/200 kHz 40
- 50 kHz display 41
- 200 kHz display 41
- Where to nd sh 42
- Fish arches 42
- 9-5 Range 43
- Range > 43
- Zoom range and offset 43
- 9-6 Gain and threshold 43
- The gain window 44
- Threshold 44
- Echosounder10 45
- 10-1-1 Extended history mode 46
- Bottom lock > On or Off 47
- 10-3 Echosounder split window 47
- Setting gain and threshold 48
- Fish recognition 48
- Bottom type 48
- Gauges window11 49
- Data window12 50
- Fuel functions and display13 51
- B - Part ll a tank 53
- Add fuel 53
- C - Removing fuel 53
- Set remaining 53
- Set Remaining menu to 53
- For Example 1 55
- 13-6 Fuel consumption curves 55
- 13-7 Calibration 58
- Fuel > Setup engines 58
- Calibrate and change 58
- Tides window14 59
- User card window15 60
- 16-1 Viewing AIS Vessels 62
- TCPA 15 min 63
- CPA 0.5 nm 63
- Safety msgs (rx) 64
- to turn SmartCraft Off 65
- or > to conrm 66
- to conrm 66
- 17-3-4 Trim indicator 68
- Radar 18 70
- 18-6-1 Changing the gain mode 72
- Adjust Radar > Gain Mode 72
- oating VRM/EBL 76
- from the center to give 77
- Setting up the NX40/4519 80
- 19-1 Setup > System 81
- 19-2 Setup > Chart 82
- If you select a map datum 83
- It should 83
- Set > 84
- General submenu 84
- Land submenu 85
- Other submenu 85
- 19-4 Setup > Radar 87
- Radar > Installation 90
- 19-5 Setup > GPS 91
- 19-6 Setup > Fuel 92
- 19-7 Setup > Track 93
- 19-8 Setup > AIS 94
- 19-11 Setup > Units 96
- 19-12 Setup > Comms 96
- 19-13 Setup > Calibrate 97
- Calibrate 97
- 19-14 Setup > Time 98
- 19-15 Setup > Favorites 99
- 19-16 Setup > Simulate 99
- Simulate 99
- Installation 20 100
- GA B C D E F 101
- Flush Mounting the NX40/45 102
- Bracket Mounting the NX40/45 103
- Installing an antenna 105
- Echosounder to 105
- 20-9 Installation: SmartCraft 106
- 20-10 Installation: Radar 107
- Power cable 108
- Specications21 109
- COMMUNICATIONS 110
- STANDARDS COMPLIANCE 110
- Simrad NX45 111
- Simrad NX40 111
- List of datums 112
- Troubleshooting22 113
- B-3 Fuel consumption problems 114
- Economy 114
- B-4 echosounder shnding 115
- B-5 Radar problems 116
- Navigation data24 118
- Compliance statements25 119
Related products and manuals for Car navigation systems Simrad NX45
(100 pages)© 2020, manymanuals.com. All rights reserved. | 0.481 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals