Simrad AP50 Installation Manual Page 55
- Page / 134
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Simrad AP50 Autopilot
46 20222469 / B
stored in the memory of the AP50 system. No specific action
is required to save the selected values to memory. Once the
value is changed, it is stored until the next time the menu
item is selected and changed.
• The Installation Set-up is considered global (except
language), which enables the values to be available to all
control units in the system.
• The values in the Seatrial Settings are dependent on the
successful completion of the Dockside Settings.
• In the table on page 289 the range of each setting is listed.
Note the final value selected during the Installation Set-up,
and also note any changes of values.
Before attempting to turn on the AP50 and perform an
Installation Set-up, the hardware installation and electrical
installation must be completed and performed in accordance
with the installation instructions.
3.2 Installation Menu
RUDDER
02
SETUP
REQUIRED
LANGUAGE
DOCKSIDE
INTERFACE
SEATRIAL
SERVICE
SETTINGS
SW 1.2.02
Oct 29 2004
No
Yes
A single press on the
STBY
(STBY) button switches the system on.
After approximately 5 seconds, the unit that was turned on will
show the Standby mode display. When the AP50 is delivered
new from the factory (and any time after a master reset of
memories has been performed), the Installation Set-up values are
all reset to preset (default) values. The warning message "Setup
Required" will appear at “turn on” and if an attempt to access the
AUTO or NAV modes is made.
The Installation Menu is presented on the autopilot display by
pressing and holding the
NAV
SETUP
(NAV/SETUP) button for 5
seconds.
Note ! The Installation Menu is different from the User Set-up Menu.
Refer to the flow diagram on page 48 for a pictorial view of the
Installation Menu.
Navigate through the Installation Menu as follows:
• Answer “Yes” to a question by rotating the course knob
clockwise.
• Answer “No” to a question by pressing the (STBD)
button. This will allow you proceed to the next menu item.
• Return to the previous menu item by pressing the (PORT)
button.
• Change the selected item shown by rotating the course knob
in either direction.
- Installation manual 1
- SIMRAD AP50 2
- About this document 3
- Installation Manual 4
- Contents 5
- 20222469 / B v 6
- 20222469 / B vii 8
- 1 GENERAL INFORMATION 10
- 1.2 How to Use This Manual 11
- 2 INSTALLATION 12
- 2.5 AP50 System Layout 14
- JUNCTION UNIT 16
- Max 600mm (23,5") 17
- Electrical Connection 18
- Mechanical Alignment 20
- Mechanical mounting 21
- Electrical installation 21
- 20222469 / B 13 22
- RF14XU ELECTRONIC MODULE 23
- 20222469 / B 15 24
- 2.9 J50 Junction Unit 25
- 20222469 / B 17 26
- Junction Unit Terminals 27
- System Select 27
- Toggling) 28
- 2.10 Drive Unit Installation 29
- Connecting a Reversible Pump 31
- 2.11 Control Unit 34
- HOW TO REMOVE PINS: 36
- Insert tool in slot 36
- Pull the wire 36
- Extraction tool 36
- FRONT VIEW 37
- JP21 Jack Point Installation 38
- 2.12 RC25 Rate Compass 39
- CONTROL 40
- RFC35 Fluxgate Compass 41
- 2.13 FU50 Steering Lever 42
- 2.14 TI51 Thruster Interface 42
- 2.15 AD50 Analog Drive 42
- 2.16 S9 Steering Lever 42
- Connection 43
- 20222469 / B 35 44
- POWER PCB 49
- Analog Heading Repeater 50
- Digital Heading Repeater 50
- GI51 Gyro Interface 50
- 20222469 / B 43 52
- CDI35 Interface 53
- 3 SOFTWARE SET-UP PROCEDURE 54
- 3.2 Installation Menu 55
- Language selection 56
- Dockside 56
- 48 20222469 / B 57
- 20222469 / B 49 58
- P S 59
- 20222469 / B 53 62
- Interface Set-up 63
- 20222469 / B 55 64
- 20222469 / B 57 66
- 58 20222469 / B 67
- Software Set-up Procedure 68
- 60 20222469 / B 69
- Sea Trial 70
- +000° 71
- 20222469 / B 63 72
- +005° 76
- 20222469 / B 69 78
- 20222469 / B 71 80
- 3.3 Final Test 81
- 3.4 Providing User Training 82
- 4 ADVANCED SETTINGS 84
- NMEA Data 85
- Master Reset 86
- 4.2 Settings Menu 87
- 20222469 / B 79 88
- Bypass/clutch: 89
- Handshake 1: 89
- 20222469 / B 81 90
- 20222469 / B 83 92
- 20222469 / B 85 94
- Thruster 95
- 20222469 / B 87 96
- SETTINGS 98
- 5 SPARE PARTS LIST 100
- 20222469 / B 101
- 20222469 / B 93 102
- 6 TECHNICAL SPECIFICATIONS 104
- 6.2 AP50 Control Unit 105
- 6.3 AP51 Remote Control 106
- 6.4 Junction Units 107
- 6.5 RC25 Rate Compass 108
- 6.7 CD100A Course Detector 110
- 6.8 CD109 Course Detector 110
- 20222469 / B 103 112
- 6.12 NI300X NMEA Interface 114
- 6.13 TI51 Thruster Interface 115
- 6.14 AD50 Analog Drive 115
- SIMRAD R3000X 116
- STBY AUTO 116
- 6.16 S9 Steering Lever 117
- 6.18 NMEA Sentences 118
- Remarks: 119
- 7 INDEX 120
- 20222469 / B 113 122
- Simrad AP50 Autopilot 123
- 114 20222469 / B 123
- Work Turn Gain, 85 123
- 8 APPROVALS 124
- 8.2 Certificates 125
- Simrad doc.no.519103/F 126
- Simrad doc.no.519107F 128
© 2020, manymanuals.com. All rights reserved. | 0.291 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals