Simrad SH90 - PRODUCT DESCRIPTION REV A Specifications Page 48
- Page / 122
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
IS15 General Manual
46 20220760L
The Buttons
A given press on any of the two buttons will change the mode
from ‘Heading’ to ‘Locked Course’ mode and vice versa.
The left button is used to enter set-up and installation screens.
The right button sets the lighting level. When in a set-up or
installation screen both buttons are used to change settings.
Figure 4-1 - The Buttons
4.2 Powering Up
At first time turn on please refer to section 7.13. At normal
power up, the pointer will TURN to the top, and the LCD will
show the software version for approximately one second.
The display and the pointer will then show the current heading.
Note ! It may take up to 20 seconds before the heading is displayed.
4.3 Display backlighting
Press the button and hold for 2 seconds. The display then
presents the backlighting level. Repeat pressing until desired
backlighting level. Selectable values are 1-7 and off (0).
4.4 The Heading Display
The Heading Display is the first display that is shown after
power up. The pointer shows the present heading, and so does
the LCD with the left arrow lit.
• The heading may be referenced to either Magnetic or True
North. If only one type of data is available, and the other data
is required then the local magnetic variation may be entered,
or it may be read in from a GPS if one is fitted. This may
enable the display of True heading when only a magnetic
referenced heading sensor is available.
• If no data is available the LCD will show four dashes, ‘----‘
and the pointer will point upwards.
- Instruments 1
- General Manual 1
- 20220760L 1 3
- Document revisions 4
- Document history 4
- Contents 5
- 1 INTRODUCTION 7
- 1.2 Equipment supplied 8
- 20220760L 7 9
- 20220760L 10
- 2.1 General Description 11
- 2.2 Powering Up 11
- 2.3 Display backlighting 11
- 2.4 Display Screens 12
- Notes ! 13
- Increase 14
- Decrease 14
- To Reset the Trim Speed 17
- 2.6 Screen Group 2: Wind 19
- 2.7 Screen Group 3: VMG 21
- 2.10 Alarm Sounding 29
- 3.1 General Description 31
- 3.2 Powering Up 31
- 3.3 Display backlighting 31
- 3.4 Display Screens 32
- 3.5 Screen Group 1: Depth 35
- 3.6 Screen Group 2: Speed 37
- 3.7 Screen Group 3: Wind 39
- 3.8 Screen Group 4: Nav 1 41
- 3.9 Screen Group 5: Nav 2 42
- 3.10 Screen Group 6: Race 44
- 3.11 Screen Group 7: Log 45
- 3.12 Alarm Sounding 46
- 4.1 General Description 47
- 4.2 Powering Up 48
- 4.3 Display backlighting 48
- 4.4 The Heading Display 48
- The Locked Course Display 49
- 4.5 Alarm Sounding 50
- 5 TECHNICAL SPECIFICATIONS 51
- 20220760L 51 53
- 5.2 IS15 Compass 54
- 5.3 IS15 Transceiver 54
- 5.4 IS15 Expander 55
- 20220760L 55 57
- Technical Specifications 59
- 20220760K 60
- 20220760K 59 61
- 6 INSTALLATION 63
- 6.3 System layout 65
- SDT-2 System 66
- 6.5 Transducers 67
- 6.6 Cabling 68
- Extending Cables 69
- Securing the Cables 69
- Securing the connectors 70
- 6.8 NMEA connections 71
- Installation 73
- 6.9 IS15 Transceiver 75
- 74 20220760L 76
- Power connection 77
- 76 20220760L 78
- 20220760L 77 79
- 12V supply 80
- 6.11 IS15 Expander 81
- Choosing the Cable Routes 82
- NMEA connections 84
- Figure 6-27 NMEA out 85
- Figure 6-28 NMEA in 85
- Setting-Up 89
- Expanding the system 89
- Figure 6-34 Expanded system 90
- 7 SETTING-UP 91
- (Automatic) 92
- (Manual) 92
- Bearing 92
- 7.3 General Screen Group 94
- 7.4 Depth Screen Group 96
- 7.5 Boat Speed Screen Group 97
- 7.7 Wind Screen Group 99
- 7.8 Navigation Screen Group 100
- 7.9 Compass Screen Group 100
- Screen 1 101
- Screen 2 101
- Screen 3 101
- 7.11 Expander Screen Group 102
- 7.10 Rudder Screen Group 102
- First time turn on 103
- Screen 4 106
- Screen 5 106
- Screen 6 106
- Screen 7 106
- Screen 8 107
- Screen 9 107
- Screen 10 107
- 8 FAULT FINDING 109
- IS15 General Manual 110
- 108 20220760L 110
- (MHU) needs new calibration 111
- 110 20220760L 112
- 20220760L 111 113
- 112 20220760L 114
- 20220760L 113 115
- ROBLINK TEST 116
- Fault Finding 117
- 9 MAINTENANCE 119
- 9.4 Return for Service 120
- 9.5 Local Master Reset 120
- 10 SPARE PARTS LIST 121
Related products and manuals for Navigational compasses Simrad SH90 - PRODUCT DESCRIPTION REV A
(6 pages)© 2020, manymanuals.com. All rights reserved. | 0.386 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals